Shingle Replacement

What does it take to replace a torn or a damaged roof? Apparently it takes nothing. In case you are confident to scale the roof height and do some help to your own roof,go ahead and do it. It is however advisable to take an opinion from an experienced roofer.

As per the doityourself.com,it is a basic operation to replace a shingle and takes approximately 5 minutes. I tried it and as it turned out,it was not so simple. First,it requires some expertise to align at the right angle on the roof to do a good job. This is a very important aspect of the repair as the person attempting the repair has to be positioned comfortably and securely. A drop from the roof is not the best of things to happen! Once the person has secured himself or herself to a respectable and comfortable position,it is time to start handling the tools. The tools required for replacing a shingle are as follows:-

• • · Flat pry bar to lift the shingle

• • · Hammer

• • · Nails

• • · Razor Knife

• • · Adhesive

That’s it! The procedure was simple once I was positioned comfortably on the roof. It is illustrated below:-

• • · Lift the shingle tab of the shingle two rows above the shingle I wished to replace shingle.

• • · Remove the nails from around the shingle tab

• • · Use the flat pry bar to lift the shingle and keep it securely at a place from where it will not slide down.

• • · Use the hammer claw to remove all nails around the shingle such that the shingle or a part of it can be removed with ease.

• • · Place the new shingle in place of the old one and fix the new nails at a place where there is no hole from previous fixings.

• • · Apply adhesives to the required place.

,Certain precautions to take while replacing a new shingle are as follows:

• • · Choose a shingle of a similar shade when replacing it.

• • · When installing a new roof,keep at least 20 shingles for such conditions of replacements.

• • · Don’t replace the entire shingle when only a part is to be replaced. Cut the bad part and put a new one over it.

• • · Don’t lean on the edge of a roof while replacing a shingle close to the gutter.

• • · In case there is a requirement to install a shingle near the edge of a roof,use a ladder or scaffolding.

• • · Consult an experienced roofer prior to starting work. This will also ensure that you don’t do more damage to the roof.

Shingle replacement is an easy operation and can be attempted by a person after taking the requisite precautions. It is however advisable to take assistance from an experienced roofer. Once you get the hang of it,its simple and easy.

How to Replace Damaged Roof Shingles

A Homeowners Guide To Replacing Roof Shingles

You don’t need to be an expert in the field of roofing replacement. However there are a few things to know prior to when you get started. Roof cleaning,roof shingles,roof repair, whatever it is you’re looking for,don’t simply to get on the roof without knowing exactly what you’re doing.

How to go about it now if you are going to be tackling replacing roof shingles, here’s the procedure you will follow to go about it. Installing an initial strip is the initial step to replacing roof shingles. It’s basically a backing to the roofing shingles’ first row that is visible. It is used for the main purpose of stopping water from entering the roof via the cracks between tiles. Pre-cut starter strips are available however,you are also able to cut the tabs on the entire shingle.

There are many designs and sizes to choose from. This will depend on the kind of roof you own. Start everything off by cleaning the roof. If there’s too much dirt or debris on your roof, the shingles may not adhere well. It is now time to begin shingling. Remove the adhesive from the old shingle,and then remove it. Put a unused shingle in its place . This will allow you to replace roof shingles.

How to Determine If Your Asphalt Roof Shingles Need Replacement

Most people don’t think about their roof until they experience an incident with a security breach,or see water seeping into their homes. Be sure to be prepared and don’t be caught out. Here are some tips to help you recognize the possibility of a roofing problem.

1 It sounds obvious however,make sure to check whether there are any missing shingles. The previous roofing contractor must have installed a protective layer of the use of tar paper or an ice-shield. But, it isn’t something that is able to stand up to the elements for the course of.

2 Look for cracks,curling or buckles. This could be caused by poor ventilation or old age. The tar strip that is beneath your roof might not be working properly in the event that the shingles do not lay on their own. These shingles are highly susceptible to winds and will most likely fall off when it comes to. If you’re experiencing issues with ventilation,a roofing contractor can tell you what to do about it.

3 Take a look at the amount of grit on your shingles. Roof shingles that are smooth and black indicate that the granules are coming loose, leaving the tar layer. Another method of determining if you’re losing granules is by checking your gutters or downspouts. If you find a lot of particles in these areas roofing shingles,they are losing their protective layer and are reaching the point of expiration in their life span.

4– If you have access to your attic,check the underside of the roof sheathing. Look for water marks following a heavy rain. Also,look for soft or damp spots on your plywood. Pay close attention around any plumbing vents on the roof,roof vents,skylights and chimney. They are among the prime areas where water could get in.

5– Look in the attic to find if there is any daylight. You may sometimes be able see light coming from the roof’s gutters on the low end. This is a possibility when there is a lot of rain or snow and ice buildup. Flashing or ice and water shields can be put in place to fix this. Also see if you can detect pin holes in your roof flashing around chimneys or skylights. A well-placed tar can fix this problem,however in the event that the flashing has rotted out, it’s time to be replaced.

6- Roof age A properly installed 3 tab roof shingles will last between 20 to 25 years. A roof shingle that is of an architectural design will last for about 30 years if it is correctly installed. There are some parameters that will add or subtract years from those figures A qualified roofer will identify the exact amount. More likely is that the roof is made up of two layers.

Understanding the Basics of Replacing Roof Shingles

There are many tasks that can be completed around the house,including replacing roof shingles. It may be necessary to understand how to repair the roof underneath the shingles and replace them if they are damaged. It is essential to know the problem and address it as soon as is possible. These things can quickly grow if left untreated. This is enough information to aid you in tackling the roofing replacement project.

Begin by getting onto the roof to determine the root of the issue. Lift the area of concern’s lower flap to view the nailing pattern. Believe it or not, it is here that the issue is most often. The nail will usually be too high on the shingle, causing lift. It could also be that they utilized too much pressure using the nail gun to drive the nail into the roof.

Start your roof replacement of shingles by removing the highest shingle. There are tools that can be used to take off the shingles without harming them. To ensure that the shingles are not damaged,remove them from the top and the bottom. You can usually be able to see the entire roof when it’s exposed.

The next step is to learn how to replace the shingles once roof repairs are finished. It is done in the exact opposite manner the way you removed them off. Begin by the bottom and ensure to line up the shingles properly prior to nailing them. It is important to follow any local rules regarding nail patterns. Once you have one nail in place and secured,it’s time to move onto the next. To nail the last shingle,lift the lower portion of the shingle. It might also be necessary to nail one more shingle over it to secure it correctly.

A lot of people employ contractors to repair roof shingles. Understanding the limitations of home repair is important. You don’t have to be an expert on how to fix the roof beneath the shingles or replace them after it’s done. This is a fantastic DIY project for the weekend that you can proudly do yourself.

Roof Shingle Replacement FAQs

How should I know that I need new shingles?

You need new roofing materials when the current ones show evidence of curling,splitting and loss of surface granules. You also require new shingles when the current ones have broken down or are missing.

Can I re-roof over an existing layer?

Yes you can do it. Experts agree that there is no harm in putting a second roof over an original one. When putting the new roof you should ensure that the original roof provides a smooth nailing surface and there is no decay under the first roof.

You should also ensure that your structure can withstand the added load. When re-roofing,you should ensure that you replace all broken or missing shingles.

Although,it’s recommended that you re-roof over an existing layer,you should not do it more than once. This means that you should not put a third roof. This is because this will give your house a hideous look. The load can also be too heavy for your house to bear and as a result to collapse of your building.

Which quality indicators that I should look for when buying shingles?

The national roofing contractors association recommends that you should go for materials that comply with the American society for testing and materials (ASTM) standards.

Here organic shingles are identified as ASTM D 225 while fiberglass shingles are rated as ASTM D 3462. To be certain that you have bought the right materials,you should always talk to your roofer so that he/she can help you with the purchase.

Do shingle manufacturers provide warranties?

Yes they do. Warranties on asphalt shingles range from 20 to 40 years depending on the manufacturer. When buying the materials you should carefully review the manufacturer’s warranty stipulations and understand the responsibilities and financial obligations that they will assume if the materials fail to reach their expected lives.

,